2013 sprinter 144” high roof 246k 3.0L
This thing is a stealth road trip machine, perfect for coastline cruising or long hauls across the US I’ve done it all in this rig. Clean Montana title. I am the 2nd owner, original owner was the state of Texas as a fleet vehicle. Van has absolutely NO RUST damage, has typical drainage orange stains near bottom of doors but no actual deep rust. Van is absolutely rock solid, did 22 day/6700 mile trip in October with not a single hiccup, warning light, or problem all while getting 22MPG. Planned on keeping van forever but lost my job so gotta sell.
Will deliver anywhere in the lower 48 states w/ deposit and proof of funds
MECHANICAL:
-Oil/oil filter changed 1/12/2025
-EZ-DRAIN oil plug for no mess oil changes
⬇️All maintenance⬇️
-all new glow plugs 6-24’
-transmission flush & service 6-24’
-serpentine & accessory belt 5-25’
-all 4 wheel bearings 6-24
-wheel speed sensors 5-25’
-fuel filter 4-25’
-new oil cooler 6-25’
-new high pressure fuel pump 6-24’
-16” aluminum upgraded THOR wheels
-Michelin 245/75/16 w/ less than 8k miles
-sliding door mechanism 5/2024
-weather seals (rear doors, slider, and front doors)
-new fuel pump & gas tank brackets 5/2024
-will include all “what if” parts I carry in van for long trips ie. serpentine belt, fuel filter, fuel filter hoses, extra clamps etc.
BUILD OUT:
-above cab insulated w/ exhaust heat shield sheet
-killmat throughout van (cab/doors/ceiling/panels)
-floor insulate w/ 1/8 closed cell foam/exhaust tape
-3M Thinsulate for large flat areas
-havelock wool insulation in all cavities
-wall panels 1/4” finished birch cnc cut by Routed Wild and Rivnut to van w/ M6 bolts & flush washers
-walls upholstered in a waterproof material called tolex (commonly used on guitar cabs) very tough
-ceiling 1/4” finished birch w/ custom art, attached w/ rivnut
-floor 3/4” birch w/ Loncoin brand flooring glued on w/ step extension and storage cubby built in
-flarespace flares & trim rings (6’6” sleep space)
-flares insulated w/ closed cell foam and upholstered in water proof material
-3/4” finished birch bed platform w/ upholstered top, on 5 SKORVA beams. Held to van w/ reinforced M10 plus nuts & grade 10.9 hardware. Bed can be removed in about 35 minutes w/ a 6 & 8 mm allen
-8” hybrid foam short queen mattress (new)
-overhead storage built w/ 8020 aluminum,ikea UTRUSTA hinges, and ikea HAVSTORP cabinet doors(passenger 2 doors 10”x48” driver 3 doors 10”x72”) w/ leather pull tabs
-Galley built w/8020 framing and ikea cabinet fronts to match overheads. W60” T36” D22” w/ ikea cement countertop. 4 doors w leather pulltabs
-Fridge 48Q w/ 8020 framed enclosure w/ ICECO slide out
-electrical: renogy 50A DC-DC, 3000w inverter, 200AH liFePO4 battery, 0G/2G wiring. Breakers in between every line, and 2 isolators (front and rear of van) 2 120 outlets w/ 2 USB C plugs at galley, 120v single outlet installed at rear opening of van
-Enclosed garage w/ overhead lighting on dimmer
-Maxxfan 7500k w/ remote & Van Essential cover
-LED lighting tracks w/ dimmer control
-Cab shelf w/ curtain rod & blackout curtain
-brand new headliner I painted black
-4 corners of van have LED flood lights & 1 on rear door for camping
-Curt tow hitch & Flatline van co rear step
-13” touchscreen head unit w/ wireless car play, new door & dash speakers & added 6” overhead cab speaker
-black carpet floor-mat
-RoutedWild foot platform w/ storage, side seat storage, & driver & passenger rear storage boxes
-seats replaced w/ Winnebago sprinter wide seats (do have heavy signs of wear but very comfy)
-new CAT seat covers
-backup camera & panoramic rear view mirror
-Van Essentials rear doors,slider door, and fan insulated & magnetic covers
-entire van is sprayed w/ raptor lined including side trim and front and rear bumpers
-fold down galley shelf (detachable in 1 min)
CONS:
-power steering has intermittent leak, replaced reservoir but needs 1 hose.
-front ac vents have broken tabs, purely cosmetic and I saved all cosmetic work for last.
-2 circular holes in front quarter panels from previous work lights. Attempted to weld in plugs but panel was warping w/ heat
-side mirrors need to be worked on a bit to sit flush proper and fold in
-TPMS warning despite brand new sensors
-windshield has chips
